This website uses cookies to make the content more user-friendly and effective. By using this website, you agree to the use of cookies. You can find additonal information about the use of cookies and the possibility of objecting to the use of cookies here.

gardening. landscaping. greendesign.

16 - 19 September 2020 // Nuremberg, Germany

Posting print layout

What information should be shown in the print layout?

Create print layout
Exhibitors & Products GaLaBau 2018
Zoom product LOGO_ROMPOX® - EASY

ROMPOX® - EASY

LOGO_ROMPOX® - EASY

ROMPOX® - EASY

Request information Request information

Contact us

Please enter your personal information and desired appointment. You can also leave us a message.

Your personal information

Your message for us

Desired appointment during the exhibition

* Compulsory fields you must fill in.

Information on data protection can be found here.

Send
Your message has been sent.

You do not have a registration yet? Register now and use all advantages of the Exhibitors and Products Database, the supporting programme and the TicketShop.

An error has occurred.

ROMPOX® - EASY

The easiest paving joint mortar

ROMPOX® - EASY is a ready to use 1 component paving joint mortar. After application it hardens when it reacts with the oxygen in air and is thus vacuum packed. This highly water permeable jointing mortar is very good for DIY use as it is so easy to use. ROMPOX® - EASY can be used on patios, footpaths, non trafficked entry areas or similar pedestrian only surfaces all around the house. The paving joint mortar can be used with almost all types of natural stones, natural and concrete stone slabs as well as clinker surfaces. Polygonal slabs / crazy paving or broken stone slabs are the exception. In this case we recommend using our 2 component paving joint mortars such as ROMPOX® - D1.

Our paving joint mortar ROMPOX® - EASY is ...

  • for pedestrian loads
  • for jointwidths from 5 mm
  • for jointdepths from 30 mm
  • fulfills the criteria of the usage category 1 acc. to ZTV road construction

ROMPOX® - EASY is available in the following colours:

  • sand - neutral

APPLICATION:

Construction site requirements:

The foundation needs to be prepared according to the expected traffic loads. Regulations and leaflets regarding construction of paved stone surfaces should be heeded. Future loads must not cause the surface to settle or loosen stones. Ideally “ROMEX® - TRASS-BED – the frost resistant drainage mortar“ should be used.

Preparation:

Clean out joints to a depth of at least 30 mm | 1 3/16" ( minimum joint width 5 mm | 3/16" ). The surface to be jointed should be cleaned of all kinds of dirt. Any adjoining surfaces that are not to be jointed should be taped off.

Pre-wet:

Pre-wet surface. Porous surfaces as well as higher surface temperatures require more intense pre-wetting.

Application:

Open the lid of the bucket. Pour the paving jointing mortar immediately onto the surface and using a coarse street broom or squeegee spread it evenly so that it goes into the joints deeply, firmly and compactly. Professional tip: In order to compact the joints even better, the freshly applied paving jointing mortar can be elutrified using a water spray jet. Sunken joints are re-filled with more paving jointing mortar. Avoid any standing water in the fresh joints, ensure there is sufficient slope.

Final cleaning:

Finally, clean the stone surface carefully with a fine hair broom, so that it is free of all mortar residue. Sweep diagonally to the joint. Do not re-use swept off material. Any residual material on the stone surface can still be swept off after 24 hours with a coarse street broom.

Subsequent treatment:

Rain protection during drizzle is not necessary. In case of heavy or permanent rain, the jointed surface should be protected for approx. 24 hours. The rain protection ( building sheet/ cover sheet) can be laid directly onto the surface. During the initial period, a very fine synthetic resin film

remains on the stone surface which intensifies the colour of the stones and protects against dirt. This film disappears over the course of time due to weathering and abrasion.

Important instructions:

In case of doubt always lay a sample surface before doing the entire jointing. Do not use in “permanently wet areas“ ( swimming pools, fountains, drains, drip edges etc. ) Remove anything that stores water regularly from the jointed surface such as moss, leaves and weeds. Only use on water permeable substructures. The mortar can slowly disintegrate if exposed to permanent water loads or standing water. Only use outdoors.

You decided to attend the GaLaBau? Get your tickets at the TicketShop



top

The selected entry has been placed in your favourites!

If you register you can save your favourites permanently and access all entries even when underway – via laptop or tablet.

You can register an account here to save your settings in the Exhibitors and Products Database and as well as in the Supporting Programme.The registration is not for the TicketShop and ExhibitorShop.

Register now

Your advantages at a glance:

  • Advantage Save your favourites permanently. Use the instant access – mobile too, anytime and anywhere – incl. memo function.
  • Advantage The optional newsletter gives you regular up-to-date information about new exhibitors and products – matched to your interests.
  • Advantage Call up your favourites mobile too! Simply log in and access them at anytime.