TRILO

Trilo BL200

The TRILO BL200 is a hand operated leaf blower with a castor wheel at the front. This castor wheel, together with the large rear wheels, ensures easy manoeuvring, even in rugged terrain. The sturdy frame is equipped with an extendable tiller-arm which is suspended in vibration dampers. The fan housing is placed at an angle to create a forward airflow that bends slightly to the side, preventing leaves falling back onto the cleared area. This handy blower is equipped with  a Ø 380 mm 5 blade fan in a TRILO centrifugal pump which is driven by a reliable Honda 9 HP petrol engine with a recoil.

Trilo BL300

The TRILO BL300 has a light weight fan, which allows it to start up supple and fast. The height adjustable castor wheels ensure that the blower follows the contours of the soil perfectly and prevent damage to the spout and turf. The standard equipped 180 degree reverse spout can be adjusted hydraulically from the driver’s seat. The spout is placed in the centre of the machine so there is no difference in air capacity between the left and right side of the blower. The BL300 is driven by a Walterscheid PTO shaft with shear bolt and overrun clutch and is equipped with a Ø 450 mm fan in an TRILO centrifugal pump. This leaf blower can be used on tractors from 20 HP (14 kW) with a double acting hydraulic valve for operating the reverse spout.

The BL300 is also available for hydraulic drive (BL300HY). The towing vehicle should be equipped with 2 double acting hydraulic valves. The BL300HY is delivered with ½” plug nipples.

Trilo BL400

The BL400 is a unique leaf blower, because it can be mounted both on the front or the back of the towing vehicle. This makes this blower not only suitable for tractors, but it can also be used on mowers, hydraulic vehicles etc. The gauge wheels and anti-scalp roller ensure the blower follows the contours of the soil perfectly and, together with the sturdy brace, prevents damage to the spout and turf. The BL400 is suitable for tractors (PTO versions) from 25 HP (18 kW) and can be used with RPM`s ranging from 540 to 2500. Most versions are equipped with a Walterscheid PTO shaft with overrun clutch, which drives a Ø 400 mm fan in a TRILO centrifugal pump. The optional 180 degree reversible spout can be hydraulically or electrically adjusted from the driver’s seat. The BL400 has a low noise level which makes it a perfect leaf blower for populated areas, such as golf courses or urban areas.

Trilo BL740

The TRILO BL740 is a large capacity leaf blower: 338 m3/minute. The large gauge wheels and anti-scalp roller ensure the blower follows the contours of the soil perfectly and prevents damage to the spout and turf. The blower is equipped with a Walterscheid PTO shaft with overrun clutch which drives a Ø 740 mm fan in a TRILO centrifugal pump and can be used on tractors from 35 HP (25 kW). The BL740 can optionally be equipped with a 180 degree reversible spout which can be hydraulically operated from the driver’s seat. By setting the spout downward, the blower will clean both sides of the road simultaneously.

Trilo BL960

The TRILO BL960 is our most powerful blower. This blowing giant is suitable for tractors from 45 HP (33 kW) and is equipped with a Ø 960 mm fan in a TRILO centrifugal pump with a fan belt. This blower is driven by a Walterscheid PTO shaft and can optionally be equipped with a 180 degree reversible spout which can be hydraulically operated from the driver’s seat. By setting the spout downward, the blower will clean both sides of the road simultaneously. The large gauge wheels and anti-scalp roller ensure the blower follows the contours of the soil perfectly and prevent damage to the spout and turf.

Trilo B7

The TRILO B7 leaf blower is a compact, low weight blower with a large capacity. This makes this blower very suitable for tractors from 30 HP (22 kW). This powerful leaf blower is equipped with a Walterscheid PTO shaft with overrun clutch and is driven by a Ø 650 mm fan in a TRILO centrifugal pump. The gauge wheels and anti-scalp roller ensure the blower follows the contours of the soil perfectly and prevent damage to your spout and turf. The reverse spout (standard on the B7A-version) can be hydraulically operated from the driver’s seat. By setting the spout downward, the B7 will clean both sides of the road simultaneously.

The TRILO S3 is a compact and economical vacuum sweeper with a loading capacity of 3 m3 and large, air filled tyres for low soil pressure. The S3 is standard equipped with a brush hood, which brushes the mowed grass or leaves together for more efficient vacuuming. Optionally you can also equip the S3 with a mowing shaft, verticutting shaft or a combined shaft for simultaneously mowing and verticutting. The castor wheels are mounted in the heart of the shaft, ensuring that the sweeper follows the contours of the soil perfectly. This vacuum sweeper is suitable for tractors from 28 HP (20 kW) and is driven by a Walterscheid PTO shaft with wide angle and overrun clutch. The Ø 700 mm 4 blade fan is placed inside a TRILO centrifugal pump with replaceable lining for extra-long life. The optional wander hose has a reach of 6 meters and is equipped with a sturdy end pipe with handgrip.

The TRILO S4 vacuum sweeper is our S3`s big brother. The S4 also is a compact and economical vacuum sweeper with large, air filled tyres for low soil pressure. The difference is in the larger 4 m3 container and a bigger fan for more suction power. The S4 is equipped with a Ø 850 mm, 4 blade fan which is placed in a TRILO centrifugal pump with replaceable lining for extra-long life. This larger fan requires some more horsepower than the S3: 45 HP (33 kW) minimum. A Walterscheid PTO shaft with wide angle and overrun clutch provide power transmission. Gauge wheels, placed in the heart of the suction hood which is placed in towing direction, ensure that the axle follows the contours of the soil perfectly. This vacuum sweeper can also be equipped with a braked axle suitable for fast traffic.

Trilo SU40

The TRILO SU40 suction unit is mounted onto a chassis suitable for fast traffic (maximum 80 km/h) with bolt joint. The chassis is also equipped with lighting and can easily be driven anywhere you need it. The SU40 is equipped with a reliable 11 HP Honda petrol engine that drives a Ø 400 mm fan through a fan belt. The fan is placed inside a wear-resistant dual walled housing. The SU40 is standard equipped with a 4 meter long wander hose that can be mounted on the right or the left side of the unit. A hose arm and support bracket are also included. For your safety the fan of the SU40 automatically stops when the wander hose is disconnected. The fan housing can easily be cleaned using the drain with cap. The spout can be turned 360 degrees and is equipped with an end piece for guiding the airflow.

Trilo SU60

The TRILO SU60 suction unit is mounted onto a solid chassis suitable for fast traffic (maximum 80 km/h) with bolt joint. The chassis is also equipped with lighting and can easily be driven anywhere you need it. The SU60 is equipped with a reliable 2 cylinder 20 HP Honda petrol engine with electronic start. The Ø 600 mm fan is placed inside a wear-resistant dual walled housing and is driven through a fan belt. The SU60 is standard equipped with a 5 meter long wander hose with a sturdy end pipe and hand grip. A hose arm and support bracket are also included. For your safety the fan of the SU60 automatically stops when the wander hose is disconnected. The spout can be turned 360 degrees and is equipped with an end piece for guiding the airflow.

Trilo VCU120

The TRILO VCU120 verticutting unit is mounted on a robust steel frame which can be linked to a category I three point hitch. The VCU120 has a working width of 1,20 meter and can be used behind a tractor from 15 HP (11 kW). This verticutting unit is mounted off set, so you will not drive over your freshly verticut soil. A PTO shaft with shear bolt powers the chain driven axles. The verticutting depth can be easily adjusted through a threaded spindle on both sides of the unit. The VCU120 can optionally be equipped with floating wheels at the back and a flexible 3 point linkage for even better contour following. The VCU120 can easily handle a thatch layer of up to 5 cm deep.

Trilo VCU150

The TRILO VCU150 verticutting unit is mounted on a robust steel frame which can be linked to a category I or II three point hitch. The VCU150 has a working width of 1,50 meter and can be used behind a tractor from 20 HP (14 kW). A Walterscheid PTO shaft with shear bolt powers the chain driven axles. The verticutting depth can be easily adjusted through a threaded spindle on both sides of the unit. The VCU150 can optionally be equipped with floating wheels at the back and a flexible 3 point linkage for even better contour following. The VCU150 can easily handle a thatch layer of up to 4 cm deep.

Trilo VCU200

The TRILO VCU200 verticutting unit is mounted on a robust steel frame which can be linked to a category I or II three point hitch. The VCU200 has a working width of 2,00 meter and can be used behind a tractor from 20 HP (14 kW). A Walterscheid PTO shaft with shear bolt powers the chain driven axles. The verticutting depth can be easily adjusted through a threaded spindle on both sides of the unit. The VCU200 can optionally be equipped with floating wheels at the back and a flexible 3 point linkage for even better contour following. The VCU200 can easily handle a thatch layer of up to 4 cm deep.

Trilo VCU240

The TRILO VCU240 verticutting unit is mounted on a robust steel frame which can be linked to a category I or II three point hitch. The VCU240 has a working width of 2,40 meter and can be used behind a tractor from 25 HP (18 kW). This verticutting unit is mounted off set, so you will not drive over your freshly verticut soil. A Walterscheid PTO shaft with shear bolt powers the chain driven axles. The verticutting depth can be easily adjusted through a threaded spindle on both sides of the unit. The VCU240 can optionally be equipped with floating wheels at the back and a flexible 3 point linkage for even better contour following. The VCU240 can easily handle a thatch layer of up to 4 cm deep.

Trilo VCMK3

The VCMK3 verticutting unit is a mechanically driven, flexible verticutter with 3 independent terrain following elements. The verticutting knives turn with the driving direction for a tight verticut and as little root damage as possible. The VCMK3 is available in working widths of 1,70 and 2,00 meter and can be mounted under the SG400. This flexible verticutting unit is suitable for tractors from 25 HP (18 kW) and is driven by a Walterscheid PTO shaft with shear bolt. This unit is equipped with gauge wheels and sliders that are placed in the heart of the axle so that the elements follow the contours of the soil perfectly. The axle can be equipped with 2 mm Tungsten tip knives as well as 3 mm Manganese steel tip knives. The verticutting depth can be adjusted easily through a threaded spindle on both sides of the unit.

Trilo C15

The TRILO C15 is a unique machine that can flail mow, verticut and collect in one pass. This robust machine is suitable for tractors from 30 HP (22 kW) and can be used on all sorts of surfaces. From sports fields to rough terrain, such as verges. The over 1 m3 large hopper can be hydraulically emptied and the shape of the dust cap guides the airflow to the back instead of upwards. The knives are easily accessible for cleaning, maintenance or changing. Braces on the sides of the machine protect the axle from damage as a result of collisions. Besides mowing and collecting grass, the powerful wind paddles can also be used to collect leaves or horse droppings.